降壓直流轉換器現今已廣泛使用於許多場合，如通訊伺服器、個人電腦、消費性電子及電動車電池等。當其應用於高降壓比的情況時，會造成輸出電流漣波大，因此需要較大的輸出電容，且當降壓比不夠高時，開關的工作週期需操作於臨界值，會造成更高的電磁干擾。另外，當其應用於大功率的情況時，如果為單相轉換器會有嚴重的傳導損失。因此，本文提出一新型轉換器，以解決上述問題。
本論文之主要貢獻可摘要如下:第一點貢獻為提出新型低輸出電流漣波高降壓比轉換器，與現有文獻相比元件數量較少，因此具備成本低及可靠度高之優點，且具有最低輸出電流漣波，如此可減少電容值，以減少電容體積並提高功率密度，且可達到D2/2之高降壓比，以減少二極體導通時間，其中 為轉換器的責任週期。此外，本轉換器不需添加額外的均流電路，即能達到自動均流之優點。第二點貢獻為針對新型轉換器之工作原理與穩態特性進行分析，且進一步推導出直流模型與小訊號數學模型，以作為閉迴路之設計依據。第三點貢獻為實際製作一輸入400V、輸出24V、輸出功率400W雛型架構，經由模擬與實測結果比對，以驗證本論文所提新型轉換器的可行性，而在負載為125W時，最高效率可達92.6%。

Step-down DC converters are widely used in various applications such as server power、personal computer、VRMs of CPU boards and battery chargers. For higher step down ratio applications, the resulting output current of the above converters becomes rather large and often require a rather large output capacitor. Besides, when the step down ratio is too large, the corresponding switch duty cycle is required to operate at the threshold resulting in much high electric magnetic interruption. Furthermore, for higher power applications, the conduction losses of the converter will be severe if a single-phase converter is used. Hence, the goal of this thesis is aimed to developing a novel high step-down voltage ratio converter with low output ripple.
Basically, the contributions of this thesis may be summarized as follows. First, a novel high step-down voltage ratio converter topology is proposed. Compare with the existing converters, it has low component count which can result in low cost and high reliability. Also, the low output current ripple of the proposed converter can reduce the output capacitor volume and increase the converter power density. An improve voltage gain of D2/2 can be achieved where is the duty ratio of the converter, so that the diode conduction time can be reduced. In addition, the inductor currents in two phases can achieve uniform current sharing automatically. Second, derivation of both DC and AC models and mathematical analysis of the new converter are also made in the context for design of the closed-loop control. Third, a 400W prototype with a 400V input voltage and 24V output voltage is constructed to verify the feasibility of the new converter. Experimental results show that a maximum efficiency of 92.6% can be achieved when the load is 125W.

摘 要 I
英文摘要 II
誌 謝 III
目 錄 IV
圖 目 錄 V
表 目 錄 VIII
第一章 緒論 1
1.1 研究動機 1
1.2 文獻回顧 2
1.3 本論文之貢獻 3
1.4 論文內容概述 3
第二章 五類交錯式降壓轉換器簡介 4
2.1 前言 4
2.2 具主動箝位之交錯式順向式轉換器簡介 4
2.3 具自動消磁之交錯式順向轉換器簡介 9
2.4 具共用開關腳之交錯式順向轉換器簡介 14
2.5 串級降壓型之交錯式轉換器簡介 19
2.6 新型四相交錯式高效率降壓直流轉換器簡介 23
第三章 新型轉換器建模與分析 32
3.1 前言 32
3.2 新型高轉換器工作原理 33
3.3 新型轉換器之數學模型推導 43
3.4 新型轉換器穩態特性分析 61
3.5 新型轉換器與相關文獻穩態特性比較 81
第四章 實體電路製作與量測結果 83
4.1 前言 83
4.2 功率電路製作 84
4.3 控制電路實現與設計 86
4.4 模擬與實測結果 93
第五章 結論 104
5.1 論文內容總結 104
5.2 未來工作 105
參考文獻 107

[1] S. R. Bull, “Renewable energy today and tomorrow,” Proceedings of the IEEE, vol. 89, no. 8, pp. 1216-1226, Aug. 2001.
[2] G. Connor and H. W. Whittington, “A vision of true costing [renewable energy],”Engineering Science and Education Journal, vol. 10, no. 1, pp. 4-12, Feb. 2001.
[3] M. Begovic, A. Pregelj, A. Rohatgi, and C. Honsberg, “Green power: status and perspectives,” Proceedings of the IEEE, vol. 89, no. 12, pp. 1734-1743, Dec. 2001.
[4] H. Falk, “Prolog to renewable energy today and tomorrow, ”Proceedings of the IEEE, vol. 89, no. 8, pp. 1214-1215, Aug. 2001.
[5] Y. Liu, A. Pratt, P. S. N. Kumar, M. Xu, and F. C. Y. Lee, “390V input VRM for high efficiency server power architecture,” Applied Power Electronics Conference, APEC 2007 - Twenty Second Annual IEEE, pp. 1619-1624, Feb/Mar. 2007.
[6] T. F. Wu, Y. K. Cheng, G. R. Yu, and Y. R. Cheng, “Power electronics as efficient interface in dispersed power generation systems,” Power Electronics and ECCE Asia (ICPE & ECCE), 2011 IEEE 8th International Conference, pp. 235-241, May/Jun. 2004.
[7] Experience in Developing and Promoting 400Vdc Datacenter Power, Tomm V. Aldridge, Director, Energy Systems Research Lab, Intel Corporate Technology Group, Green Building Power Forum, Jun. 2009.
[8] Development of a DC Power Inlet Connector for 400Vdc IT Equipment, Brian Davies, Director of Engineering, Anderson Power Products, Inc. Green Building Power Forum, Jan. 2010.
[9] A. Acik and I. Cadirci, “Active clamped ZVS forward converter with soft-switched synchronous rectifier for high efficiency, low output voltage applications,” Proc. IEE Electr. Power Appl., vol. 150, no. 2, pp. 165–175, Mar. 2003.
[10] Q. M. Li and F. C. Lee, “Design consideration of the active-clamp forward converter with current mode control large-signal transient,” IEEE Transactions on Power Electronics, vol. 18, no. 4, pp. 958–965, Jul. 2003.
[11] K. B. Park, C. E. Kim, G. W. Moon, and M.-J. Youn, “Three-switch active-clamp forward converter with low switch voltage stress and wide ZVS range for high input voltage applications,” IEEE Transactions on Power Electronics, vol. 25, no. 4, pp. 889–898, Apr. 2010.
[12] M. Jinno, J. C. Sheen, and P. Y. Chen, “Effect of magnetizing inductance on active-clamped forward converters,” in Proc. INTELEC, pp. 636–642, 2003.
[13] H. M. Suryawanshi, M. R. Ramteke, K. L. Thakre, and V. B. Borghate, “Unity-power-factor operation soft switched converter based on boost active clamp topology in modular approach,” IEEE Transactions on Power Electronics, vol. 23, no. 1, pp. 229–236, Jan. 2008.
[14] S. S. Lee, S. W. Choi, and G. W. Moon, “High-efficiency active-clamp forward converter with transient current build-up (TCB) ZVS technique,” IEEE Transactions on Industrial Electronics, vol. 54, no. 1, pp. 310–318, Feb. 2007.
[15] Q. M. Li and F. C. Lee, “Design consideration of the active-clamp forward converter with current mode control large-signal transient,” IEEE Transactions on Power Electronics, vol. 18, no. 4, pp. 958–965, Jul. 2003.
[16] R. T. Bascope and I. Barbi, “A double ZVS-PWM active-clamping forward converter: analysis, design, and experimentation,” IEEE Transactions on Power Electronics, vol. 16, no. 6, pp. 745–751, Nov. 2001.
[17] T. Qian and B. Lehman, “Dual interleaved active-clamp forward with automatic charge balance regulation for high input voltage application, IEEE Transactions on Power Electronics, vol. 23, no. 1, pp. 38–44, Jan. 2008.
[18] H. Wu, P. Xu, W. Liu, and Y. Xing, “Series-Input Interleaved Forward Converter with a Shared Switching Leg for Wide Input Voltage Range Applications,” IEEE Transactions on Industrial Electronics, Sep. 2012.
[19] K. B. Park, C. E. Kim, G. W. Moon, and M. J. Youn, “Multi-level active clamp forward converter with reduced voltage stress,” in Proc. IEEE Power Electron. Spec. Conf., pp. 938–943, 2008.
[20] K. B. Park, C. E. Kim, G. W. Moon, and M. J. Youn, “A novel two-switch forward configuration for wide input-voltage range applications RCD-clamped forward converter with ripple reduction (RCDFRR),” Power Electronics Specialists Conference, 2008. PESC 2008., pp. 2278–2283, Jan. 2008.
[21] T. Jin, K. Zhang, K. Zhang, and K. Smedley, “A new interleaved series input parallel output (ISIPO) forward converter with inherent demagnetizing features,” IEEE Transactions on Power Electronics, vol. 23, no. 2, pp. 888-895, 2008.
[22] P. L. Wong, P. Xu, B. Yang, and F. C. Lee, “Performance improvements of interleaving VRMs with coupling inductors,” IEEE Transactions on Power Electronics, vol. 16 no. 4 , pp. 499-507, Jul. 2001.
[23] K. Nishijima, K. Harada, T. Nakano, T. Nabeshima, and T. Sato, "Analysis of double step-down two-Phase buck converter for VRM", in Proc. IEEE International Telecom. Energy Conference, pp.497-502, Sep. 2005.
[24] B. Oraw, and R. Ayyanar, “Small signal modeling and control design for new extended duty ratio, interleaved multiphase synchronous buck converter,” IEEE Applied Telecommunications Energy Conf., pp. 1 - 8, Sept. 2006.
[25] Y. Jang, M. M. Jovanovi, and Y. Panov, "Multiphase buck converters with extended duty cycle," in Proc. Applied Power Electronics Conference and Exposition, 2006. APEC '06, pp.38-44, Mar. 2006.
[26] C. H. Hsieh, T. J. Liang, L. S. Yang, R. L. Lin, and K. H. Chen, “Analysis and implementation of a DC-DC step-down converter for low output-voltage and high output-current applications,” IEEE Applied Circuits and Systems Conf., pp. 3697 - 3700, June. 2010.
[27] T. Jin, K. Zhang, K. Zhang and K. Smedley, “A new interleaved series input parallel output (ISIPO) forward converter with inherent demagnetizing features,” IEEE Transactions on Power Electronics, Vol. 23, No. 2, pp. 888-895, 2008.
[28] 鄭皓謙，’’非隔離型四相高效率降壓直流轉換器”，國立清華大學碩士論文，中華民國一百零一年七月。
[29] C. S. Lin and C. L. Chen “Single-wire current-share paralleling of current-mode controlled DC power supplies,” IEEE Transactions on Industrial Electronics, vol. 47, no. 4, pp. 780-786, Aug. 2000.
[30] Y. Panov and M. M. Jovanovic, “Stability and dynamic performance of current-sharing control for paralleled voltage regulator modules,” IEEE Transactions on Power Electronics, vol. 17, no. 2, pp. 172-179, Mar. 2002.
[31] P. Li, and B. Lehman, “A design method for paralleling current mode controlled DC–DC converters,” IEEE Transactions on Power Electronics, vol. 19 no. 3, pp. 748-756, May. 2004.
[32] M. Ponjavić and R. Djurić, “Current sharing for synchronised DC/DC converters operating in discontinuous conduction mode,” IEE Proceedings Electric Power Applications, vol. 152 no. 1, pp. 119-127, Jan. 2005.
[33] H. Mao, L. Yao, C. Wang, and I. Batarseh, “Analysis of inductor current Sharing in nonisolated and isolated multiphase DC–DC Converters,” IEEE Transactions on Industrial Electronics, vol. 54 no. 6pp. 3379-3388, Dec. 2007.
[34] W. H. Li, and X. N. He, “A family of isolated interleaved boost and buck converters with winding-cross-coupled inductors,” IEEE Transactions on Power Electronics, vol. 23, no. 6, pp. 3164–3173, Nov. 2008.
[35] W. H. Li, and X-N He, “A family of interleaved DC–DC converters deduced from a basic cell with winding-cross-coupled inductors (WCCIs) for high step-up or step-down conversions,” IEEE Transactions on Power Electronics, vol. 23, no. 4, pp. 1791–1801, July. 2008.
[36] K. Yao, Y. Qiu, M. Xu, and F. C. Y. Lee, “A novel winding-coupled buck converter for high-frequency, high-step-down DC-DC conversion,” IEEE Transactions on Power Electronics, vol. 20, no. 5, pp. 1017–1024, Sept. 2005.
[37] K. Nishijima, D. Ishida, K. Harada, T. Nabeshima, T. Sato, and T. Nakano, “A novel two-phase buck converter with two cores and four windings,” IEEE Applied Circuits and Systems Conf., Sept/Oct 2007, pp. 861–866.
[38] K. Yao, M. Ye, M. Xu, and F. C. Lee, “Tapped-inductor buck converter for high-step-down dc–dc conversion,” IEEE Transactions on Power Electronics, vol. 20, no. 4, pp. 775–780, Jul. 2005.
[39] C. Y Ko, T. J Juu, K. H Cheng, J. F Cheng, “Design and analysis of an interleave controlled series buck converter with low load current ripple,” Circuits and Systems (APCCAS), 2010 IEEE Asia Pacific Conference., pp. 672–675 Dec 2010.
[40] A. E. D. Jr., C. H. G. Treviso, C. A. Gallo, and F. L. Tofoli, “Non-isolated DC-DC converters with wide conversion range used to drive high-brightness LEDs,” Power Electronics Conference, 2009. COBEP '09. Brazilian., pp. 598–605, Sept/Oct. 2009.